Product Description
Product Parameters for P0917MF Termination Assembly
📘 Product Overview
| Field | Details |
|---|---|
| Manufacturer | Foxboro (by Schneider Electric) |
| Part Number | P0917MF |
| Product Type | Termination Assembly (TA) for FBM207c |
| Function | Interfaces 16 channels of 48 V dc contact sense inputs for FBM207c |
| Associated FBM | FBM207c (Channel Isolated, Voltage Monitor/Contact Sense Input Module) |
| System Compatibility | Foxboro Evo Process Automation System, Standard 200 Series FBM Subsystem |
⚙️ Functional Specifications
| Feature | Specification |
|---|---|
| Signal Inputs | |
| - Type | 48 V dc Contact Sense (internal source) |
| - Number of Channels | 16 group-isolated input channels |
| - Input Voltage | 48 V dc nominal open circuit voltage |
| - Short Circuit Current | 2.5 mA ± 20% |
| - On-State Resistance | Up to 1 kΩ |
| - Off-State Resistance | 100 kΩ minimum |
| Signal Outputs | None (FBM207c is input-only for this TA) |
| Isolation | Group isolation for input channels; specific isolation ratings not detailed in the document but typically 600 V ac for 1 minute between channels and ground (based on FBM standards) |
| Connection Type | Compression or ring-lug terminals; connects to FBM via 37-pin D-subminiature cable |
| Supported Cables | Type 4/4H (Baseplate to TA): P/PVC, LSZH, or H/XLPE; up to 30 m (98 ft) |
| Power Requirements | Supplied by FBM207c; no direct power input to TA |
| Calibration | No calibration required |
🔌 Physical Specifications
| Feature | Specification |
|---|---|
| Material | Polypropylene (PVC) or Polyamide (PA) |
| Mass | Approximately 420–908 g (0.93–2.0 lb), depending on TA configuration (based on similar TAs) |
| Dimensions | Typical for 200 Series TAs: Width ~267–286 mm, Height ~125 mm (exact dimensions not specified for P0917MF) |
| Mounting | DIN rail (32 mm or 35 mm) |
| Cable Connections | Compression terminals: 0.2 to 4 mm² (24 to 12 AWG); Ring-lug: #6, 0.5 to 4 mm² |
🌡️ Environmental Specifications
| Parameter | Specification |
|---|---|
| Operating Temperature | PVC: -20 to +50°C (-4 to +122°F); PA: -20 to +70°C (-4 to +158°F) |
| Storage Temperature | -40 to +70°C (-40 to +158°F) |
| Relative Humidity | 5 to 95% (non-condensing) |
| Operating Altitude | -300 to +3,000 m (-1,000 to +10,000 ft) |
| Storage Altitude | -300 to +12,000 m (-1,000 to +40,000 ft) |
| Contamination | Class G3 (Harsh) per ISA S71.04; EIA Standard 364-65, Class III |
| Vibration | 0.75 m/s² (5 to 500 Hz) |
✅ Regulatory Compliance
| Certification Type | Details |
|---|---|
| Certification Types | Type 1, Type 2 (see definitions below) |
| Underwriters Laboratories (UL/UL-C) | Listed for Class I, Groups A-D, Division 2, Temperature Code T4 hazardous locations; suitable for enclosure-based systems |
| ATEX (DEMKO) | Certified Ex nA IIC T4 Gc for Zone 2 potentially explosive atmospheres; complies with ATEX Directive for II 3 G use |
| Type 1 Certification | UL/UL-C listed for Class I, Groups A-D, Division 2, T4; ATEX Ex nA IIC T4 for Zone 2 |
| Type 2 Certification | UL/UL-C listed as associated apparatus for supplying non-incendive field circuits for Class I, Groups A-D, Division 2; ATEX certified for non-incendive field circuits for Zone 2, Group IIC; field circuits are Class 2 limited energy (60 V dc, 30 V ac, 100 VA or less) if customer equipment meets Class 2 limits |
| Marine Certification | Bureau Veritas Certified for Marine Installations in Environmental Category EC31C; ABS Marine Type Approved |
| EMC Compliance | Meets European EMC Directive 2014/30/EU; EN61326:2013 Class A Emissions and Industrial Immunity levels |
| Low Voltage Directive | Complies with European Low Voltage Directive for safety |
📦 Ordering Information
| Field | Details |
|---|---|
| Part Number | P0917MF |
| Associated FBM | FBM207c (Channel Isolated, Voltage Monitor/Contact Sense Input Module) |
| Other TAs for FBM207c | P0917MH, RH917MG, P0917MJ |
| Conditions of Use | Must be installed and used as specified in the Standard and Compact 200 Series Subsystem User’s Guide (B0400FA) |